USER'S INSTRUCTIONS: The project work you are about to view is on design of sample and hold circuit using op-amp. Please, sit back and study the below research material carefully. This project topic (design of sample and hold circuit using op-amp) have complete 5(five) Chapters . Each Project Material include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this design of sample and hold circuit using op-amp project research material is to reduce the stress of moving from one school library to another all in the name of searching fordesign of sample and hold circuit using op-amp research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
DESIGN OF SAMPLE AND HOLD CIRCUIT USING OP-AMP
BY
---
EE/H2007/01430
DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
SCHOOL OF ENGINEERING
INSTITUTE OF ---
DECEMBER,2018
APPROVAL PAGE
This is to certify that the research work,design of sample and hold circuit using op-amp by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on Electrical and Electronics Engineering has been approved.
By
Engr. --- Engr. ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
Engr. ---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work design and construction of a microcomputer trainer kit research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages ( use it to develop yours), Abstract and Chapter one of design of sample and hold circuit using op-ampvisible for everyone, then the complete material on design of sample and hold circuit using op-amp is to be ordered for. Happy viewing!!!
This work is on an overview of sample and hold circuit using op-amp. As the name implies, a sample and hold circuit is a circuit which samples an input signal and holds onto its last sampled value until the input is sampled again. Sample and hold circuits are commonly used in analogue to digital converts, communication circuits, PWM circuits etc. The circuit shown below is of a sample and hold circuit based on uA 741 opamp, n-channel E MOSFET BS170 and few passive components. In the circuit MOSFET BS170 (Q1) works as a switch while opamp uA741 is wired as a voltage follower. The signal to be sampled (Vin) is applied to the drain of MOSFET while the sample and hold control voltage (Vs) is applied to the source of the MOSFET.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWLDGEMENT
ABSTRACT
CHAPTER ONE
INTRODUCTION
1.1 AIM OF THE STUDY
- PURPOSE OF THE PROJECT
- APPLICATION OF THE PROJECT
- SIGNIFICANCE OF THE PROJECT
- SCOPE OF THE PROJECT
CHAPTER TWO
LITERATURE REVIEW
- OVERVIEW OF THE PROJECT
- OPERATIONAL AMPLIFIER
- HISTORICAL BACKGROUND OF AN OP-AMP
- THE IC 741 OP-AMP CHARACTERISTICS
- PIN DIAGRAM OF IC 741 OP-AMP
- DECRIPTION OF BS170 - MOSFET TRANSISTOR
CHAPTER THREE
SYSTEM DESIGN
- BLOCK DIAGRAM SAMPLE AND HOLD CIRCUIT
- SAMPLE AND HOLD OPERATION
- SAMPLE AND HOLD CIRCUIT DIAGRAM
- SAMPLE AND HOLD CIRCUIT WORKING
CHAPTER FOUR
TESTING AND RESULTS
- SYSTEM SETUP PROCEDURES
- COMPONENTS ASSEMBLING PROCEDURE
- TESTING OF SYSTEM OPERATION
- INSTALLATION OF THE COMPLETED DESIGN
CHAPTER FIVE
- CONCLUSION
- REFERENCES
CHAPTER ONE
1.0 INTRODUCTION
In electronics, a sample and hold circuit is an analog device that samples (captures, takes) the voltage of a continuously varying analog signal and holds (locks, freezes) its value at a constant level for a specified minimum period of time. Sample and hold circuits and related peak detectors are the elementary analog memory devices. They are typically used in analog-to-digital converters to eliminate variations in input signal that can corrupt the conversion process.[2]
A typical sample and hold circuit stores electric charge in a capacitor and contains at least one switching device such as a FET (field effect transistor) switch and normally one operational amplifier.[1] To sample the input signal the switch connects the capacitor to the output of a buffer amplifier. The buffer amplifier charges or discharges the capacitor so that the voltage across the capacitor is practically equal, or proportional to, input voltage. In hold mode the switch disconnects the capacitor from the buffer. The capacitor is invariably discharged by its own leakage currents and useful load currents, which makes the circuit inherently volatile, but the loss of voltage (voltage drop) within a specified hold time remains within an acceptable error margin.
1.2 AIM OF THE STUDY
The main objective of this work is to write on a circuit which samples an input signal and holds onto its last sampled value until the input is sampled again. Sample and hold circuits are commonly used in analogue to digital converts, communication circuits, PWM circuits etc. The circuit shown below is of a sample and hold circuit based on uA 741 opamp, n-channel E MOSFET BS170 and few passive components.
1.3 PURPOSE OF THE STUDY
Sample and hold circuits are used in linear systems. In some kinds of analog-to-digital converters, the input is compared to a voltage generated internally from a digital-to-analog converter (DAC). The circuit tries a series of values and stops converting once the voltages are equal, within some defined error margin. If the input value was permitted to change during this comparison process, the resulting conversion would be inaccurate and possibly unrelated to the true input value. Such successive approximation converters will often incorporate internal sample and hold circuitry. In addition, sample and hold circuits are often used when multiple samples need to be measured at the same time. Each value is sampled and held, using a common sample clock.
1.4 APPLICATION OF THE STUDY
The applications of sample and hold circuit include the following
- Sampling Oscilloscopes
- Data Distribution System
- Digital Voltmeters
- Analog Signal Processing
- Signal Constructional Filters
- Data Conversion System
1.5 SIGNIFICANCE OF THE STUDY
The function of the Sample and hold circuit is to sample an analog input signal and hold this value over a certain length of time for subsequent processing. Taking advantages of the excellent properties of MOS capacitors and switches, traditional switched capacitor techniques can be used to realize different S/H circuits.
With the help of sample and hold circuit we can take samples of the analogue signal, followed by a capacitor. It holds these sample for a particular period. As a consequence of this, a constant signal is generated this can be converted into the digital signal with the help of analogue to digital converters.
1.6 SCOPE OF THE STUDY
A typical circuit of the sample and hold stores electric charge in a capacitor and holds at least one switching device like a field effect transistor switch and usually one op-amp (operational amplifier).
To sample the i/p signal the switch unites the capacitor to the o/p of a buffer amplifier. This amplifier amplifies the capacitor so that the voltage across the capacitor is almost equal, or proportional to input voltage. In hold form, the switch separates the capacitor from the buffer. The capacitor is always discharged by its own outflow currents and helpful load currents, which makes the circuit essentially unstable, but the voltage drop in a particular hold time remains within a suitable error margin.
1.7 PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to this study. In this chapter, the background, significance, scope of this work was discussed.
Chapter two is on literature review of the study. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
CHAPTER TWO: The complete chapter two of design of sample and hold circuit using op-amp is available. Order full work to download. Chapter two of design of sample and hold circuit using op-amp consist of the literature review. In this chapter all the related work on design of sample and hold circuit using op-amp was reviewed.
CHAPTER THREE: The complete chapter three of design of sample and hold circuit using op-amp is available. Order full work to download. Chapter three of design of sample and hold circuit using op-amp consist of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of design of sample and hold circuit using op-amp is available. Order full work to download. Chapter four of design of sample and hold circuit using op-amp consist of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of design and construction of a design of sample and hold circuit using op-amp is available. Order full work to download. Chapter five of design of sample and hold circuit using op-amp consist of conclusion, recommendation and references of design of sample and hold circuit using op-amp.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research for your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
You can also visit our facebook Page at fb.me/hyclas to view more our related construction (or design) pics
For more information contact us through Any of the following means:
Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]
Email address :engr4project@gmail.com
Watsapp No :+2348146561114
To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.